Oil Based Pre-Stain Wood Conditioner

All raw wood projects require preparation sanding before applying stain or wood conditioners. If you skip this critical step, your finish may be rough and uneven.

Preparation for Raw Wood 
See our video: How to Prep Sand Raw Wood

1. Sand open grain wood with 120-grit sandpaper followed by 150-grit, then 180 grit. Sand closed grain wood with no finer than 180 grit sandpaper. 
2. Remove dust with a vacuum, compressed air, a tack cloth or a water-dampened rag.  
3. Do not over-sand with fine-grit sandpapers; this will close and seal the wood grain, preventing ideal product absorption.

Join General Finishes University Facebook Group at https://www.facebook.com/groups/generalfinishesuniversity for customer support and learning opportunities for GF products. This group is a great resource for guidance regarding choosing the right product, mastering finishing techniques, troubleshooting, or sharing your finished projects.

General Finishes Oil Based Pre-Stain Conditioner Application Steps

For use with oil-based stains.

1. Work in a well-ventilated area. 
2. Stir General Finishes Oil Based Pre-Stain Conditioner to reincorporate solids that have settled to the bottom of the can.
3. Do NOT thin.
4. Apply 1 coat of Pre-Stain Conditioner to raw wood using a clean cotton rag, natural bristle or foam brush, staining pad or pad applicator.
5. Pre-Stain Conditioner Natural can improve color uniformity over difficult-to-stain wood species such as pine. However, it will limit color absorption, so a darker wood stain may be required to get the desired depth of color.
6. Let Pre-Stain Conditioner penetrate the wood for 10+ minutes.
7. Wipe off excess with a clean, dry cloth.
8. Apply stain over conditioner. 
9. Let Pre-Stain Conditioner dry at least 30 minutes, but no longer than 2 hours before applying stain, in ideal conditions: 70°F/20°C; 50% humidity. Do not wait longer than 2 hours, and never let Pre-Stain Conditioner dry overnight before applying a stain over it. 

Dilute Oil Based Stain: Add 5% GF Oil Based Pre-Stain Conditioner to GF oil based stains by volume; increase up to 15% as desired. 

Cleanup
Clean up application materials and hands with mineral spirits or waterless hand cleaner, like Goop or Gojo. 

Disposal
Take great care when disposing of product-soaked applicators. Application materials, such as brushes and towels, containing oil-based products may spontaneously catch fire if improperly discarded. Immediately place all application materials soaked with this product in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations. 

Spills
Clean up spills with mineral spirits immediately while wet. If oil-based finishes dry, they are difficult to clean off any surface, clothes or carpet. Carpet may discolor if cleaned with mineral spirits.

Prevention 
Protect your workspace with a tarp, your hands with gloves, and your clothes with an apron.

Life of Product
General Finishes products do not last forever, even when unopened. They are best used within 1 year. The life of the product may be extended with proper care and storage.

Storage Tips
See our video: Tips for Storing Leftover Finishes
Oil-based products start to harden and cure when exposed to oxygen. The following best practices will increase the life of your product:

1. Keep container tightly closed and sealed until ready for use, in the original container. Do not store in unlabeled containers.
2. Pry open sealed lids with a paint can opener by hooking under the lid's rolled edge. The use of a screwdriver can disfigure the rim and lid, impairing a complete seal. 
3. Keep lid closed while working. Decant what you will use into a bowl, paper cup, or plate, and close can lid as you work. Every minute the can is open, the product is curing.
4. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Clean the chime of the can thoroughly with a paper towel before closing to create a complete seal. Product in the chime can be minimized by using a pouring lid, such as Fitsall. Avoid wiping used brushes on the lid.
5. Pound the lid in place using a rubber mallet to avoid distorting the chime or lid. Dents in the lid from direct contact with a hammer can impair a complete seal. Alternatively, place a flat piece of wood over can lid and firmly pound shut.
6. Avoid temperatures below 50°F/10°C or above 80°F/26°C. Frozen and heat-damaged product cannot be revitalized. Store in original container protected from direct sunlight in a dry, cool and well-ventilated areas.
7. Do not store product in an attic, garage, in direct sunlight, or next to ignition source with heat and flames such as a furnace. 
8. Store the can upside down to create a liquid seal, minimizing oxygen exposure from within the can. Decant remaining product from the can before stirring.
9. Add Bloxygen can. Bloxygen is an argon gas system that prevents oxygen and moisture from hardening leftover product. Because Bloxygen gas is heavier than air, it sinks to the surface of the leftover finish, creating a barrier between product and air trapped in the container.
10. Decant leftovers to a smaller, properly labeled container when the finish is almost used up to reduce the volume of oxygen in the container.
11. Use appropriate containment to avoid environmental contamination.

Oil-Based Pre-Stain Conditioner Warnings and Warranties


Limited Warranty
General Finishes products must be tested to your complete satisfaction before using. General Finishes will not be responsible for color satisfaction, misapplication, nor compatibility with other manufacturers' products. General Finishes will be responsible only for the cost of our products, and not for costs such as labor, damage or project replacement.


Contamination and Compatibility
Our finishes are engineered as a system and are compatible with each other. General Finishes cannot guarantee an ideal refinish when applying our products on top of or combined with another company's products or over surfaces that have been in contact with waxes, polishes or sprays containing contaminants such as silicone. Test for adherence and aesthetics before beginning.


FIRST AID: Seek immediate medical attention if symptoms occur due to the following. EYE CONTACT: Remove any contact lenses. Flush eyes with water for 20+ minutes while lifting upper and lower eyelids. SKIN CONTACT: Wash thoroughly after handling. INHALATION: Move to fresh air. Loosen tight clothing. If not breathing, if breathing is irregular, or if respiratory arrest occurs, trained personnel should provide artificial respiration or oxygen. INGESTION: Call physician immediately. Wash out mouth with water. Do not induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person.


Prop 65 WARNING: This product can expose you to Ethylbenzene, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.

DANGER: COMBUSTIBLE LIQUID AND VAPOR. HARMFUL OR FATAL IF SWALLOWED. CAUSES EYE IRRITATION.

DANGER: Can enter lungs and cause damage.
DANGER: Keep out of reach of children. Keep away from heat and flame. Use only with adequate ventilation. Do not breathe vapor or mist. Do not swallow. Avoid contact with eyes. Keep container tightly closed when not in use. Wash thoroughly after handling.