Enduro Pre Cat Laquer

GF recommends using the least expensive product that will provide the needed performance characteristics. We offer a range of products designed for professional spray applications and brush-on finishes for consumer use.

Compare all GF Topcoats Here

Watch Video: Comparison of All GF Water Based Finishes Here

PROFESSIONAL TOPCOATS

ENDURO PRE CAT LACQUER (Spray only)

Looking for hardness, clarity and fast stack time? Pre Cat Lacquer is the choice. Use in applications where there is little risk of chemical contamination issues from substances such as ketchup, soap, chemical cleaners, or ammonia. This is the perfect spray finish for interior doors, casing, moldings, door jambs and furniture that receives light use. When you think about it, interior doors don't take a lot of wear. You might wipe them down or dust them once in a while but that is about it. PreCat Lacquer is a hard finish that provides excellent build and superior clarity at a phenomenal price point. If you are not finishing a surface such as a tabletop where you anticipate chemical contamination during use, why pay for a more expensive finish?

Dries clear.

Watch Pre Cat Lacquer Product Overview Video Here

ENDURO CLEAR POLY (Spray only)

Poly is the go-to cabinet finish. It has all the durability you need at a lower price point than Conversion Varnish. It is similar to High Performance in test measurements for chemical, water and wear resistance, but HP can be brushed and Clear Poly can't - it is already thinned for spraying. Clear Poly has a bit of an edge over High Performance in overall chemical resistance, a 98 rating vs 92.

Dries clear.

Watch Clear Poly product overview video here

ENDURO CONVERSION VARNISH (2K-Spray only)

This is our top of the line. Conversion Varnish is a post catalyzed high solids, two component urethane formulated for professionals who need the highest level of durability and chemical resistance. Varnish will cure the fastest. Requires NCO Catalyst. It is recommended for commercial applications or extremely high-wear surfaces such as countertops and bar tops

Dries clear.

Watch Conversion Varnish Product Overview Video Here

Enduro 2K Clear Poly (Spray Only) 

For today's professional, industrial and OEM users, water-based Tintable 2K Clear Polyurethane is formulated to stop your biggest frustrations and provide ultimate durability for interior/exterior use. Key features are easy application, fast film build & production time, excellent adhesion, plus optimum water & chemical resistance.

Dries clear. 

Watch 2K Clear Poly Product Overview Video Here

Enduro Pro Series Clear Poly 

General Finishes Enduro Pro Series Clear Polyurethane is a single-component, self-cross linking polyurethane/acrylic topcoat designed for fast build with excellent flow and leveling. Priced competitively for the professional and industrial markets, Pro Series Clear is tintable and meets or exceeds KCMA standards. Recommended use is interior cabinets, trim, doors, and furniture. Use over raw, stained, or primed wood substrates.

Dries clear.

RETAIL TOPCOATS

HIGH PERFORMANCE (Brush or Spray)

GF's best performing brush on finish with very similar performance testing as our Poly. (High Performance can be thinned for spraying).

Dries clear.

Watch High Performance Product Overview Video Here

FLAT OUT FLAT (Brush or Spray)

Flat Out Flat is formulated with a self cross-linking acrylic, and is designed to mimic the look and feel of a wax finish. Because of the increased matting agents used to create the "Flat look", this finish will have less clarity. Like wax, it dries softer to the touch than High Performance when completely cured, and will show more fingerprints. FOF finish will mark up more easily because of increased matting agents used to reduce the sheen, so it is not recommended for high-use tabletops.

Dries clear.

Watch Flat Out Flat Product Overview Video Here

BOTH PROFESSIONAL AND RETAIL TOPCOATS

ENDURO-VAR II (Spray or brush)

Enduro-Var II is an oil modified water-based alternative for customers that want the warm look of an oil finish in a water based coating. It looks more like an oil finish than a water coating, and can be sprayed or brushed. The original Enduro-Var adheres well ONLY over WATER STAINS, DYE STAINS, and RAW WOOD. Use over other finishes at your own risk. The new formula of Enduro-Var II is compatible with all GF products and dries to a lighter amber than the previous formula.

Dries Amber

Watch Enduro-Var II Product Overview Video Here

EXTERIOR 45O TOPCOAT

Exterior 450 provides a clear drying tough, protective finish that will withstand the rigors of the sun, rain, and wind. It is suitable for vertical surfaces such as fences, patio furniture, garage doors, entrance doors, outdoor kitchens and interior windows. It is not recommended as a deck finish. Fortified with UV absorbers to stabilize the finish, Exterior 450's built-in mildewcide retards mold and mildew growth.

Dries Clear

Watch Exterior 450 Topcoat Overview Video Here

General Finishes water-based products can be sprayed through compressed air, HVLP, airless or C.A.S. units.

DOWNLOAD SPRAY TIP CHART PDF 

SURFACE PREPARATION:

All surfaces should be clean and free from dirt and oil and sanded.

Indicated below are instructional videos we have for preparing a surface for a new coat of paint or finish:

• Prep sand raw wood.
• Prep sand an existing finish.
• Power prep an existing high-use finish such as kitchen cabinets.

SPRAY APPLICATION OF GENERAL FINISHES WATER-BASED FINISHES:

All General Finishes water-based topcoats and wood stains are ready to spray from the container without additives with the exception of Conversion Varnish. Always strain material through a medium to fine mesh filter before spraying. If necessary, in hot or dry climates, reduce 10 to 15% with General Finishes Extender to extend the open time.

PRE SEALING:

Softwoods such as Pine absorb stain at an uneven rate and may respond better to staining if the wood is pre-sealed. General Finishes Pre-Stain Conditioner Natural can be applied to raw wood to condition the surface for uniform penetration of the stain. Pre-sealing will cause the final stain to be lighter so you may need to use a darker color. Always test your color on a hidden part of the furniture. Allow the Pre-Stain Conditioner to dry 30 minutes before applying your final stain color.

If you are using a sprayer that has been used for oil-based or lacquers, clean the unit thoroughly with acetone followed with hot water to purge the fluid passage. Apply a thin coat first that will dry and harden faster. Sand this first coat down to a smooth base on which to build your finish coats with a 220-320 grade foam sanding pad or #400-grit sandpaper. It is better to spray 2 thin coats rather than 1 heavy coat.

Contact your supplier to verify proper tip sizes for your specific equipment. GF's general recommended fluid tips for Wood Stains and Top Coats are Compressed air - .040 and Airless - .009.

DOWNLOAD SPRAY TIP CHART PDF

This PDF lists general guidelines for several different types of sprayers with specific General Finishes product recommendations for HVLP listed below.

RECOMMENDED TIPS FOR GENERAL FINISHES PRODUCTS USING HVLP:

• Milk Paint: 1.8mm-2.0mm
• Brushable White Enamel 1.8mm-2.0mm
• Stain Blocker: 1.8mm-2.0mm
• Pearl Effects: 1.8mm-2.0mm
• Glaze Effects: 1.8mm-2.0mm
• High-Performance Topcoat: 1.1mm-1.3mm
• Flat Out Flat Top Coat: 1.1mm-1.3mm
• Enduro-Var 1.1mm-1.3mm
• Water-Based Wood Stain: 1.1mm-1.3mm
• Water-Based Dye Stain: 1.1mm-1.3mm
• Exterior 450 Topcoat:1.1mm-1.3mm
• Exterior 450 Stain: 1.1mm-1.3mm
• Enduro Sanding Sealer: 1.3-1.4mm
• Enduro White Poly: 1.3mm-1.5mm
• Enduro Black Poly: 1.3mm-1.5mm
• Enduro White Under Coat 1.5mm-1.8mm
• Enduro Clear Poly: 1.1mm-1.3mm
• Enduro Pre Cat Lacquer: 1.1mm-1.3mm
• Enduro Conversion Varnish: 1.1mm-1.3mm

Air caps should be medium size. Contact your supplier to verify proper tip sizes for your specific equipment.

Break your work into sections such as dresser top or drawer fronts. Spraying too large of an area can result in a textured grainy surface. A correctly sprayed finish should appear even and glossy. It is important to spray enough material to allow proper flow and leveling of the finish.

Spray medium wet films at 3-5 wet ml thickness. Practice makes perfect. If you have never sprayed finishes before, take a large piece of cardboard and practice your technique first. Spray water on the cardboard to learn how the gun works. Check your fluid settings and adjust the controls to get comfortable with the spray angles and to develop your technique.

SPRAYING TOPCOATS:

Keep your gun at a 90* angle, 6-8" from the surface. On large flat areas, use wet, even patterns 6 to 8 wide. For narrow surfaces, reduce the fan pattern to 2-3" to reduce overspray. For topcoats, overlap each pass 25% to conceal lines.

Watch our video how to spray water-based topcoats here.

SPRAYING WATER BASED WOOD STAINS:

Keep your gun at a 90* angle, 6-8" from the surface. On large flat areas, use wet, even patterns 6 to 8 wide. For narrow surfaces, reduce the fan pattern to 2-3" to reduce overspray. Overlap each pass of stain 50% for even coverage and wipe back the excess with an absorbent cloth. For narrow surfaces, reduce the fan pattern to 2-3" to reduce overspray.

SPRAYING WATER BASED DYE STAINS:

Keep your gun at a 90* angle, 6-8" from the surface. On large flat areas, use wet, even patterns 6 to 8 wide. For narrow surfaces, reduce the fan pattern to 2-3" to reduce overspray. Overlap each pass of stain 50% for even coverage. If coverage is even, there is no need to wipe. If you have issues with uneven coverage, wipe back the excess with an absorbent cloth. For narrow surfaces, reduce the fan pattern to 2-3" to reduce overspray.